Difference Between Ruida RDC6445G and RDC6442S Controller for CO2 Laser Engraving Cutting Machine
Enclosed Type
How long can a woodworking engraving machine use - - Engraving machine _ _ _ _ CNC woodworking engraving machine engraving machine carving factory house
by：Transon
2020-07-17
>
woodworking engraving machine general design service life for ten years or so, this is is ideally.
woodworking engraving machine in use should pay attention to maintenance and maintenance, if the system of normal work 8 hours a day, usually with a 5 - 6 age no problem.
but the service life of woodworking engraving machine is according to the customer's usage, cannot treat as the same.
if your business is good, the processing capacity is very big, so is the easiest way to wear bearing spindle, the time between a year and a few years. As the mechanical structure, bad is only the slider, but there is no problem with a few years. And easy to change, circuit aspect, is the aging of electronic accessories and some aging wire damaged.
configuration is a key problem, of course, the high-end machine will also extend the service life of woodworking engraving machine. General woodworking engraving machine is equipped with imported Italian air cooling spindle, high Japan yaskawa servo drives, imported linear square guide rail, bearing strength, three axis dustproof. Dust is larger, buy equipment it is better for dust cover.
the following said about how the woodworking engraving machine maintenance to prolong life
engraving machine ( Engraving equipment) Is a very precise and sculpt fast numerical control equipment, so the maintenance and care is very important. If you want to prolong the life of your engraving machine, and then to elaborate care. Such as much of the lubricating oil is wiped, in terms of the long time use, and can't carved carving machine outside the properties of the workpiece.
1, keep engraving machine every time in 10 hours a day's work, and to use clean water, Inside the water tank to add mesh) , but also guarantee the normal work of the pump for a long period of time, serious to eliminate motor, the phenomenon of the lack of cooling water, To add cold water resources in time) , to regular replacement of cooling water, this will keep the water temperature is not high, so as to effectively achieve carving mechanical and electrical spindle cooling effect, in the winter, if engraving machine working environment temperature is very low, so can be replaced with antifreeze. Or, as in the northeast area, if in the harsh weather, cooling water freezing in the spindle, as water pipes will be frozen, so that the spindle must be easy to burn out!
2, that is, when after each use the engraving machine, should be cleaned up, the machine must be above some of the dust clean enough, and on a regular basis for lubricating the transmission system.
3, the machine don't placed in damp places, want to choose a well-ventilated place, not exposure.
4, regular maintenance, cleaning the leadscrew, rotating parts and track always drops of oil, to ensure the efficient machine rotation, mobile task, reduce wear and tear.
5, don't cry because it is used to work often use a side of engraving machine, it will cause the lead screw and guide rail for a long time didn't contact with the beam and not reasonable lubrication.
6, a day before work to check the control box, the machine line is loose, whether there is a mixed line problem. Whether to use for a long time makes line leather wear lead to leakage.
7, because the engraving machine belongs to the work of dust larger mechanical, so at least once a week gap corner cleaning machine.
8, the machine table do not put sundry, corrosive or magnetic material can interfere with the machine work.
9, carving machine, power consumption is compared commonly big, so you want to configure a voltage stabilizer, guarantee the earth grounding.
10, connection machine computer to work computer and network to separate, cd-rom software also use normal software, avoid virus attacks on computers and machines and influence.
want engraving machine long life, the key still depends on how you work and maintenance, in short, the maintenance is necessary.
woodworking engraving machine general design service life for ten years or so, this is is ideally.
woodworking engraving machine in use should pay attention to maintenance and maintenance, if the system of normal work 8 hours a day, usually with a 5 - 6 age no problem.
but the service life of woodworking engraving machine is according to the customer's usage, cannot treat as the same.
if your business is good, the processing capacity is very big, so is the easiest way to wear bearing spindle, the time between a year and a few years. As the mechanical structure, bad is only the slider, but there is no problem with a few years. And easy to change, circuit aspect, is the aging of electronic accessories and some aging wire damaged.
configuration is a key problem, of course, the high-end machine will also extend the service life of woodworking engraving machine. General woodworking engraving machine is equipped with imported Italian air cooling spindle, high Japan yaskawa servo drives, imported linear square guide rail, bearing strength, three axis dustproof. Dust is larger, buy equipment it is better for dust cover.
the following said about how the woodworking engraving machine maintenance to prolong life
engraving machine ( Engraving equipment) Is a very precise and sculpt fast numerical control equipment, so the maintenance and care is very important. If you want to prolong the life of your engraving machine, and then to elaborate care. Such as much of the lubricating oil is wiped, in terms of the long time use, and can't carved carving machine outside the properties of the workpiece.
1, keep engraving machine every time in 10 hours a day's work, and to use clean water, Inside the water tank to add mesh) , but also guarantee the normal work of the pump for a long period of time, serious to eliminate motor, the phenomenon of the lack of cooling water, To add cold water resources in time) , to regular replacement of cooling water, this will keep the water temperature is not high, so as to effectively achieve carving mechanical and electrical spindle cooling effect, in the winter, if engraving machine working environment temperature is very low, so can be replaced with antifreeze. Or, as in the northeast area, if in the harsh weather, cooling water freezing in the spindle, as water pipes will be frozen, so that the spindle must be easy to burn out!
2, that is, when after each use the engraving machine, should be cleaned up, the machine must be above some of the dust clean enough, and on a regular basis for lubricating the transmission system.
3, the machine don't placed in damp places, want to choose a well-ventilated place, not exposure.
4, regular maintenance, cleaning the leadscrew, rotating parts and track always drops of oil, to ensure the efficient machine rotation, mobile task, reduce wear and tear.
5, don't cry because it is used to work often use a side of engraving machine, it will cause the lead screw and guide rail for a long time didn't contact with the beam and not reasonable lubrication.
6, a day before work to check the control box, the machine line is loose, whether there is a mixed line problem. Whether to use for a long time makes line leather wear lead to leakage.
7, because the engraving machine belongs to the work of dust larger mechanical, so at least once a week gap corner cleaning machine.
8, the machine table do not put sundry, corrosive or magnetic material can interfere with the machine work.
9, carving machine, power consumption is compared commonly big, so you want to configure a voltage stabilizer, guarantee the earth grounding.
10, connection machine computer to work computer and network to separate, cd-rom software also use normal software, avoid virus attacks on computers and machines and influence.
want engraving machine long life, the key still depends on how you work and maintenance, in short, the maintenance is necessary.
Custom message
Related Products
