Mini CNC Router TSA6090 Wood Carving Machine for Advertising Water Cooling Mach3-usb 0-6000mm//min HPGL, G Code
Enclosed Type
development of laser cutting machine
by：Transon
2021-01-08
With the development of laser cutting machine, laser engraving machine, laser marking machine apply field is becoming more and more widely, the applicable material also more and more.
But different materials have different characteristics, so the need to pay attention to when using the laser cutting are different matters.
To this end, small make up according to different materials for you the matters needing attention when using laser cutting.
structural steel the material with oxygen cutting will get good results. When oxygen was used as processing of gas, cutting edge will be mild oxidation. Metal laser cutting machine for plate thickness of 4 mm, can use nitrogen as high pressure processing gas cutting. In this case, the cutting edge will not be oxidized. More than 10 mm in thickness of plate, the plate laser cutting machine laser using special plate and workpiece surface in the processing oil can get good effect.
stainless steel cutting stainless steel need: use oxygen, in the case of edge oxidation it doesn't matter; Using the edge of the nitrogen to get without oxidation without burr, no longer need to be dealt with. Oil film in the plate surface coating will get better effect of perforation, without reducing the processing quality.
aluminum despite high reflectance and thermal conductivity, aluminum under 6 mm thickness can be cut, it depends on the alloy type and the laser power. When using oxygen cutting, cutting surface is rough and hard. With nitrogen, the cutting surface smooth. Because of its high purity pure aluminum is very difficult to cut, only on the optical fiber laser cutting machine system installation & other; Reflection absorption & throughout; Device to cutting aluminum. Otherwise would destroy reflection optical components.
titanium, titanium plate with argon and nitrogen as processing of gas cutting. Other parameters can refer to nickel chrome steel.
copper and brass both material with high reflectivity and good thermal conductivity. Can use nitrogen gas cutting thickness 1 mm below the brass; Thickness of 2 mm below the copper can be cut, processing must use oxygen gas. Only install on the system have & other; Reflection absorption & throughout; Device when cutting of copper and brass. Otherwise would destroy reflection optical components.
synthetic materials cutting synthetic materials to keep in mind when cutting the danger and may discharge of hazardous substances. Machinable synthetic materials: thermoplastic and thermosetting materials and synthetic rubber.
organic matter in all organic material cutting there is a risk of fire, Using nitrogen as gas processing, processing can also use compressed air as the gas) 。 Wood, leather, cardboard and paper can use laser cutting, cutting edge will be scorched ( Brown) 。
the use of laser equipment gradually popular, laser printing packing machine, laser marking machine, leather rubber plate laser engraving machine, metal laser marking machine, etc have become part of people's life, and laser cutting machine used to also want to look for the characteristics and needs of the cutting, can achieve better processing.
structural steel the material with oxygen cutting will get good results. When oxygen was used as processing of gas, cutting edge will be mild oxidation. Metal laser cutting machine for plate thickness of 4 mm, can use nitrogen as high pressure processing gas cutting. In this case, the cutting edge will not be oxidized. More than 10 mm in thickness of plate, the plate laser cutting machine laser using special plate and workpiece surface in the processing oil can get good effect.
stainless steel cutting stainless steel need: use oxygen, in the case of edge oxidation it doesn't matter; Using the edge of the nitrogen to get without oxidation without burr, no longer need to be dealt with. Oil film in the plate surface coating will get better effect of perforation, without reducing the processing quality.
aluminum despite high reflectance and thermal conductivity, aluminum under 6 mm thickness can be cut, it depends on the alloy type and the laser power. When using oxygen cutting, cutting surface is rough and hard. With nitrogen, the cutting surface smooth. Because of its high purity pure aluminum is very difficult to cut, only on the optical fiber laser cutting machine system installation & other; Reflection absorption & throughout; Device to cutting aluminum. Otherwise would destroy reflection optical components.
titanium, titanium plate with argon and nitrogen as processing of gas cutting. Other parameters can refer to nickel chrome steel.
copper and brass both material with high reflectivity and good thermal conductivity. Can use nitrogen gas cutting thickness 1 mm below the brass; Thickness of 2 mm below the copper can be cut, processing must use oxygen gas. Only install on the system have & other; Reflection absorption & throughout; Device when cutting of copper and brass. Otherwise would destroy reflection optical components.
synthetic materials cutting synthetic materials to keep in mind when cutting the danger and may discharge of hazardous substances. Machinable synthetic materials: thermoplastic and thermosetting materials and synthetic rubber.
organic matter in all organic material cutting there is a risk of fire, Using nitrogen as gas processing, processing can also use compressed air as the gas) 。 Wood, leather, cardboard and paper can use laser cutting, cutting edge will be scorched ( Brown) 。
the use of laser equipment gradually popular, laser printing packing machine, laser marking machine, leather rubber plate laser engraving machine, metal laser marking machine, etc have become part of people's life, and laser cutting machine used to also want to look for the characteristics and needs of the cutting, can achieve better processing.
Custom message
Related Products
