Jinan Transon CNC Equipment Co., Ltd.
S I N C E 2 0 1 0
Latest products
On how long is the carving machine lubricating oil, oil maintenance is better - what - Engraving machine _ _ _ _ CNC woodworking engraving machine engraving machine carving factory house
by：Transon
2020-07-17
>
what are carving machine common lubricant:
engraving machine lubricating agent generally divided into two kinds of lubricating oil and grease. General for the total loss system oil lubricating oil, lubricating oil after the oil hole on the shell into a space of the nut. Use lubricating oil lubrication of ball screw pair, can work in carving machine every time before refueling a cheer or timing for the job.
engraving machine need high speed, it is recommended to use the range of viscosity index in the 40 ℃ 32 ~ 68 cSt ( ISO VG 32 ~ 68) ( DIN 51519) The lubricating oil.
engraving machine need low speed, it is recommended to use the range of viscosity index in the 40 ℃ in 90 cSt ( ISO 90 VG) The above lubricant.
can use lithium grease, grease grease in general thread race and install nut shell space, every six months on the grease on the ball screw replacement time, cleaning the old grease on the screw, coated with new grease.
the machine at work every day to spray rust remover, namely ordinary lubricants, each track to spray to prevent rust and can prolong life. There are some high-end machine is their own refueling system, without artificial add trouble, automatically come on lubrication is evener, 2 - at least a week Three times!
it is important to note the lubrication part of the three axis screw, light bars. Also have corresponding steps lubrication, lubrication before need to turn the lead screw and guide rail above some impurity removal.
the key position of lubrication method is as follows:
1, Y axis: the lubrication is relatively simple, easy to clean up the oil on both sides of the guide rail, and at the bottom of the screw can from stent into oil, so easier to maintain.
2, X axis: before and after removing the screw, raise a head cover, the right side was open to mix the oil injection to guide rail, screw, bearing thrust bearing place and the right side of the wire hard man to convince.
3, Z axis to open the cover, screw, guide rail, bearing thrust bearing at the bottom of the be clear at a glance, this work is: run up and down in the mixed lubrication.
to carving machine lubricating oil notice:
CNC engraving machine equipment as a high-performance mechanical equipment, the working performance of the high and low quality directly affects the benefit of increase and decrease. So the daily maintenance and maintenance of CNC engraving machine is very important, we also discussed many times in front of the specific maintenance methods and maintenance tips, which add, replace lubricating oil regularly to equipment agent is very important. Correct add and replace lubricating agent not only can better engraving machine processing, can also extend the service life of equipment. How to add the correct lubricating agent for CNC engraving machine, this is a lot of customers don't know, think that as long as is the place that need lubrication, get some oil and then casually. In that case, is completely wrong, wrong agents, not only can not play a good effect, and can reduce the use of CNC engraving machine performance.
add lubricating oil agent for CNC engraving machine, it is important to note that in the location of the equipment to add the right agent, only in this way can better lubricating agent to achieve the best effect. Of course, the oil dose should also pay attention to how much, can not add too much, to prevent the lubricating oil.
the life of the engraving machine and use time:
the life of the carving machine is generally according to the usage of the customer, cannot treat as the same. If your business is good, the processing capacity is very big, so the first is the easiest way to wear bearing spindle. The time between a year and a few years, such as mechanical structure, bad is only the slider. But there is no problem with a few years. And easy to change, circuit aspect, is the aging of electronic accessories and some aging wire damaged.
engraving machine in use should pay attention to maintenance and maintenance, if the system of normal work 8 hours a day, usually with a 5 - Six years is no problem. Configuration is a key problem, of course, the high-end machine will also extend the service life of engraving machine. General woodworking engraving machine is equipped with imported Italian air cooling spindle, high Japan yaskawa servo drives, imported linear square guide rail, bearing strength, three axis dustproof. Dust is larger, buy equipment it is better for dust cover.
how to extend the service life of engraving:
first, keep engraving machine every time in 10 hours a day's work, and to use clean water, Inside the water tank to add mesh) , but also guarantee the normal work of the pump for a long period of time, serious to eliminate motor, the phenomenon of the lack of cooling water, To add cold water resources in time) , to regular replacement of cooling water, this will keep the water temperature is not high, so as to effectively achieve carving mechanical and electrical spindle cooling effect.
in the winter, if engraving machine working environment temperature is very low, so can be replaced with antifreeze. Or, as in the northeast area, if in the harsh weather, cooling water freezing in the spindle, as water pipes will be frozen, so that the spindle must be easy to burn out!
the second, when after each use the engraving machine, should be cleaned up, the machine must be above some of the dust clean enough, and on a regular basis for lubricating the transmission system.
what are carving machine common lubricant:
engraving machine lubricating agent generally divided into two kinds of lubricating oil and grease. General for the total loss system oil lubricating oil, lubricating oil after the oil hole on the shell into a space of the nut. Use lubricating oil lubrication of ball screw pair, can work in carving machine every time before refueling a cheer or timing for the job.
engraving machine need high speed, it is recommended to use the range of viscosity index in the 40 ℃ 32 ~ 68 cSt ( ISO VG 32 ~ 68) ( DIN 51519) The lubricating oil.
engraving machine need low speed, it is recommended to use the range of viscosity index in the 40 ℃ in 90 cSt ( ISO 90 VG) The above lubricant.
can use lithium grease, grease grease in general thread race and install nut shell space, every six months on the grease on the ball screw replacement time, cleaning the old grease on the screw, coated with new grease.
the machine at work every day to spray rust remover, namely ordinary lubricants, each track to spray to prevent rust and can prolong life. There are some high-end machine is their own refueling system, without artificial add trouble, automatically come on lubrication is evener, 2 - at least a week Three times!
it is important to note the lubrication part of the three axis screw, light bars. Also have corresponding steps lubrication, lubrication before need to turn the lead screw and guide rail above some impurity removal.
the key position of lubrication method is as follows:
1, Y axis: the lubrication is relatively simple, easy to clean up the oil on both sides of the guide rail, and at the bottom of the screw can from stent into oil, so easier to maintain.
2, X axis: before and after removing the screw, raise a head cover, the right side was open to mix the oil injection to guide rail, screw, bearing thrust bearing place and the right side of the wire hard man to convince.
3, Z axis to open the cover, screw, guide rail, bearing thrust bearing at the bottom of the be clear at a glance, this work is: run up and down in the mixed lubrication.
to carving machine lubricating oil notice:
CNC engraving machine equipment as a high-performance mechanical equipment, the working performance of the high and low quality directly affects the benefit of increase and decrease. So the daily maintenance and maintenance of CNC engraving machine is very important, we also discussed many times in front of the specific maintenance methods and maintenance tips, which add, replace lubricating oil regularly to equipment agent is very important. Correct add and replace lubricating agent not only can better engraving machine processing, can also extend the service life of equipment. How to add the correct lubricating agent for CNC engraving machine, this is a lot of customers don't know, think that as long as is the place that need lubrication, get some oil and then casually. In that case, is completely wrong, wrong agents, not only can not play a good effect, and can reduce the use of CNC engraving machine performance.
add lubricating oil agent for CNC engraving machine, it is important to note that in the location of the equipment to add the right agent, only in this way can better lubricating agent to achieve the best effect. Of course, the oil dose should also pay attention to how much, can not add too much, to prevent the lubricating oil.
the life of the engraving machine and use time:
the life of the carving machine is generally according to the usage of the customer, cannot treat as the same. If your business is good, the processing capacity is very big, so the first is the easiest way to wear bearing spindle. The time between a year and a few years, such as mechanical structure, bad is only the slider. But there is no problem with a few years. And easy to change, circuit aspect, is the aging of electronic accessories and some aging wire damaged.
engraving machine in use should pay attention to maintenance and maintenance, if the system of normal work 8 hours a day, usually with a 5 - Six years is no problem. Configuration is a key problem, of course, the high-end machine will also extend the service life of engraving machine. General woodworking engraving machine is equipped with imported Italian air cooling spindle, high Japan yaskawa servo drives, imported linear square guide rail, bearing strength, three axis dustproof. Dust is larger, buy equipment it is better for dust cover.
how to extend the service life of engraving:
first, keep engraving machine every time in 10 hours a day's work, and to use clean water, Inside the water tank to add mesh) , but also guarantee the normal work of the pump for a long period of time, serious to eliminate motor, the phenomenon of the lack of cooling water, To add cold water resources in time) , to regular replacement of cooling water, this will keep the water temperature is not high, so as to effectively achieve carving mechanical and electrical spindle cooling effect.
in the winter, if engraving machine working environment temperature is very low, so can be replaced with antifreeze. Or, as in the northeast area, if in the harsh weather, cooling water freezing in the spindle, as water pipes will be frozen, so that the spindle must be easy to burn out!
the second, when after each use the engraving machine, should be cleaned up, the machine must be above some of the dust clean enough, and on a regular basis for lubricating the transmission system.
Custom message
