Jinan Transon CNC Equipment Co., Ltd.
S I N C E 2 0 1 0
Latest products
Introduction to daily maintenance some knowledge of the cutting machine cutting machine manufacturer
by：Transon
2020-10-30
Cutting machine in the process of use, related alarm abnormal or clean oil filter and other abnormal, should be timely replacement.
The long run normally without accurate maintenance of cutting machine, this also is each cutter manipulator must learn an important knowledge.
sheet metal processing industry, the use of cutting machine without, however, at the same time of learn to use more to learn about cutting machine for routine maintenance. Cutting machine daily maintenance of the filters. Cutting oil temperature should be kept between 35 ℃ ~ 60 ℃, shall not exceed 70 ℃, if too much can lead to oil and even parts of metamorphic damage. A week is on schedule to check the oil level of gas, such as laser system for cutting machine also should check after repair, oil level below the position should include laser oil. Tank of air filter, check every 3 months clean, good is replaced every 1 year. Some knowledge about daily maintenance cutting machine cutting machine manufacturer, the following introduction: laser cutting machine oil daily maintenance.
。 Work 2000 hours after the oil should be replaced for the first time the new cutting machine, bending machine after every work of 4000 ~ 6000 hours after an oil change at a time, every time an oil change, should be thoroughly clean fuel tank. Monthly cleaning various laser cutting parts ( Including the base board, valve group, motor, pump, tubing, etc. ) To prevent any dirt into the oil system, shall not use detergent to clean. Before cutting machine shutdown, should aim the upper die down after the lower die and then closed the power supply, until after work, if you need to boot, or any other manipulation, mode selection should be cutting machine in manual, and ensure safety. Generally used in laser cutting oil for ISO HM46 or MOBILDTE25, don't mess with oil pollution, or other symbols of the laser. Laser cutting machine parts daily maintenance. New cutting machine is in use after a month, check whether there is any significant deformation on the tubing bending place, if there is any abnormality should be replaced immediately; Use after two months, should tighten the joint of all parts, bending machine during the work shall ensure that cutting machine has been in shutdown state, oil system and without pressure. Every time cutting machine oil change, should be replaced or thoroughly clean the filter. '
weld hardness is intended to reduce the laser cutting machine?
sheet metal processing industry, the use of cutting machine without, however, at the same time of learn to use more to learn about cutting machine for routine maintenance. Cutting machine daily maintenance of the filters. Cutting oil temperature should be kept between 35 ℃ ~ 60 ℃, shall not exceed 70 ℃, if too much can lead to oil and even parts of metamorphic damage. A week is on schedule to check the oil level of gas, such as laser system for cutting machine also should check after repair, oil level below the position should include laser oil. Tank of air filter, check every 3 months clean, good is replaced every 1 year. Some knowledge about daily maintenance cutting machine cutting machine manufacturer, the following introduction: laser cutting machine oil daily maintenance.
。 Work 2000 hours after the oil should be replaced for the first time the new cutting machine, bending machine after every work of 4000 ~ 6000 hours after an oil change at a time, every time an oil change, should be thoroughly clean fuel tank. Monthly cleaning various laser cutting parts ( Including the base board, valve group, motor, pump, tubing, etc. ) To prevent any dirt into the oil system, shall not use detergent to clean. Before cutting machine shutdown, should aim the upper die down after the lower die and then closed the power supply, until after work, if you need to boot, or any other manipulation, mode selection should be cutting machine in manual, and ensure safety. Generally used in laser cutting oil for ISO HM46 or MOBILDTE25, don't mess with oil pollution, or other symbols of the laser. Laser cutting machine parts daily maintenance. New cutting machine is in use after a month, check whether there is any significant deformation on the tubing bending place, if there is any abnormality should be replaced immediately; Use after two months, should tighten the joint of all parts, bending machine during the work shall ensure that cutting machine has been in shutdown state, oil system and without pressure. Every time cutting machine oil change, should be replaced or thoroughly clean the filter. '
weld hardness is intended to reduce the laser cutting machine?
Custom message
