Jinan Transon CNC Equipment Co., Ltd.
S I N C E 2 0 1 0
Latest products
Correctly grasp the using method of CNC cutting machine
by：Transon
2020-10-27
A cloth to wipe, no oil, no yellow robe.
When charged checks or maintenance, the equipment should be by double work, by a person responsible for supervision, so as to avoid accidents can get timely treatment on the schedule the daily tally sheet of the equipment maintenance record table of 11.
Straightness annual maintenance testing machine tool cutting machine straightness, will bend samples of 3 m and maintenance stage, with a feeler gauge test within any one meter gap value 0.
3mm/m
。
CNC cutting machine manipulation and maintenance regulations, CNC cutting machine maintenance tally slider guide book of lathe bed near moving parts lubrication good clean without foreign body mold clean without foreign body check on location not lower than two-thirds slider good lubrication good lubrication performance of the axial sliding block screw numerical control cutting machine manipulation and maintenance regulations by periodic maintenance to the following steps, bending machine and truthfully fill in maintenance work table properties from documentaries content photo machine down to ensure accuracy of bending surface quarter working mesa clean to machine tool, the lower die demolition. Such as monthly maintenance includes daily check, monthly, quarterly and annual contains daily tally, etc. 4. 2 equipment retained meaning items of equipment in dimensions danger, equipment signs should be placed in 'maintenance' state, with warning equipment is, homework is prohibited. Wash oil tank. Refueling through air filter oil has come into a new laser two-thirds of position, and make the slider stop 10 at top dead center. Under the fuselage flatness test placed level in machine tool working mesa, left right three, respectively measuring planeness is not higher than 0. 08, flatness before and after zero. 02 CNC cutting machine manipulation and maintenance regulations page: 18 21 note: during the implementation of maintenance, maintenance should be included at the next higher level to the next level maintenance content.
CNC cutting machine manipulation and maintenance regulations: test machine tools grounding good grounding resistance less than 1 ohm replacement laser oil and filter unscrew the every two years at the bottom of the tank on the oil drain plug, oil discharge laser. Four lock nut tighten every quarter to one by one on the X axis synchronous belt check quarter after the machine to work long hours, the synchronous behind would flush with flabby phenomenon, check after fastening machine precision CNC cutting machine manipulation and maintenance procedures page: 16 distribution box fastening quarter departments screw fastening connection strong internal components go quarter go position as shown in figure moving parts use butter gun at refueling refueling point, until the screw and guide rail see grease spill out the rest go quarter go position as shown in figure moving parts use butter gun at refueling refueling point, until the screw and guide rail see grease spill out the rest.
as the formwork surface clean oil, different heat sink clean and ensure the normal operation of the electric apparatus cabinet quarter in the condition of power distribution box fan clean again, use air gun by remove the dust outside introversion, keep the heat dissipation of CNC cutting machine manipulation and maintenance regulations, bending machine machine tool is easy to loose parts close quarter quarterly to test the machine is easy to loose parts.
four unusually good cutter blade material
。
CNC cutting machine manipulation and maintenance regulations, CNC cutting machine maintenance tally slider guide book of lathe bed near moving parts lubrication good clean without foreign body mold clean without foreign body check on location not lower than two-thirds slider good lubrication good lubrication performance of the axial sliding block screw numerical control cutting machine manipulation and maintenance regulations by periodic maintenance to the following steps, bending machine and truthfully fill in maintenance work table properties from documentaries content photo machine down to ensure accuracy of bending surface quarter working mesa clean to machine tool, the lower die demolition. Such as monthly maintenance includes daily check, monthly, quarterly and annual contains daily tally, etc. 4. 2 equipment retained meaning items of equipment in dimensions danger, equipment signs should be placed in 'maintenance' state, with warning equipment is, homework is prohibited. Wash oil tank. Refueling through air filter oil has come into a new laser two-thirds of position, and make the slider stop 10 at top dead center. Under the fuselage flatness test placed level in machine tool working mesa, left right three, respectively measuring planeness is not higher than 0. 08, flatness before and after zero. 02 CNC cutting machine manipulation and maintenance regulations page: 18 21 note: during the implementation of maintenance, maintenance should be included at the next higher level to the next level maintenance content.
CNC cutting machine manipulation and maintenance regulations: test machine tools grounding good grounding resistance less than 1 ohm replacement laser oil and filter unscrew the every two years at the bottom of the tank on the oil drain plug, oil discharge laser. Four lock nut tighten every quarter to one by one on the X axis synchronous belt check quarter after the machine to work long hours, the synchronous behind would flush with flabby phenomenon, check after fastening machine precision CNC cutting machine manipulation and maintenance procedures page: 16 distribution box fastening quarter departments screw fastening connection strong internal components go quarter go position as shown in figure moving parts use butter gun at refueling refueling point, until the screw and guide rail see grease spill out the rest go quarter go position as shown in figure moving parts use butter gun at refueling refueling point, until the screw and guide rail see grease spill out the rest.
as the formwork surface clean oil, different heat sink clean and ensure the normal operation of the electric apparatus cabinet quarter in the condition of power distribution box fan clean again, use air gun by remove the dust outside introversion, keep the heat dissipation of CNC cutting machine manipulation and maintenance regulations, bending machine machine tool is easy to loose parts close quarter quarterly to test the machine is easy to loose parts.
four unusually good cutter blade material
Custom message
