Jinan Transon CNC Equipment Co., Ltd.
S I N C E 2 0 1 0
Latest products
Woodworking engraving machine how relief sculpture is good, why the wood carving machine carved - - _ _ _ woodworking engraving machine carved machine CNC engraving machine
by：Transon
2020-07-17
>
what are the reasons using wood engraving:
1, as the mechanized equipment than the artificial production efficiency is high, and the defective rate is extremely low.
2, woodworking carving machine mostly adopt the gantry structure, the maximum meet the limits of feed can be adjusted.
3, steel structure of heavy duty lathe bed, ensure the machine's overall stability, qualitative.
4, equipment with circular guide rail or square rail, bearing surface stability. Rack drive, stable transmission, ensure long time high-speed operation not deformation, not shake.
so when carved wooden door can guarantee the accuracy of the carved with beautiful, thus greatly improve the efficiency of wood production.
the volume of a relief value is negative, below the zero plane anaglyph and above all in the zero plane relief in effect identical. Is completely different. If relief most below the zero point, and make a path can lead to the Z axis engraving machine after stroke is not enough. This is don't want to see, can use any one of the following two methods to solve the problem:
solution 1:
1, connect all colors. Make the main color ( About white) Fill the 2 d view.
2, will be the main color attribute is set to flat surface. The height and zero plane under the relief height.
3, apply this setting to relief. So the embossment will move more than zero plane.
the solution 2:
1, the open position is set form. From the main menu option in the menu option to select the model position setting.
2, move the cursor in two dimensional check. To find the lowest value of Z axis ( The Z axis value appeared in the XYZ status bar)
3, the minimum benchmark pixels in the option to select the lower left pixel.
4, set the Z value method for one find the Z axis. For example, the actual location option. Assumptions that one find the Z axis - is the minimum location value 10 is the input value 10
5, application Settings. Pick my acceptance.
6, check whether get Z values needed for the Z value. Move the cursor in two dimensional check.
to move it relief carving machine Z axis in the process of the operation of the above, if the embossment deep below the zero plane. May appear the Z axis space is not enough, this kind of situation is generally because there is not enough space at the same time keep the positive and negative relief (Z Relief from the zero plane and move to the zero plane operating process, when the new relief, must assure ArtCA M there is enough space to keep the positive and negative Z axis of two relief) 。
in general the carved by the knife to complete some time due to the design area is larger between two lines or stroke is coarser place will not processing can produce so-called islands 'carving software provides two kinds of processing methods for disposing island processing and continuous way.
the so-called island processing, wood engraving machine 3 d engraving 3 d also called woodworking engraving machine for 'three dimensional Angle of' the function is according to my design and selection of cutting tool design. Is the above said some raw to the region with the method of the bottom of the milling process.
to remove the bottom of the milling, continuous carving mode should define its percentage 'overlap', refers to the milling for flat area as an initial plane, three-dimensional processing to continue. So fashioned out of actual depth is bigger than the designed depth, but not insurmountable engraving machine blade and the height of the handle.
processing can be appropriate when revise the pick angular distance, pick angular distance, three dimensional Angle of processing parameters. When processing large objects or use coarser tool, carry angular distance can increase accordingly. Usually, it is recommended to use the default value of 0. 1 mm. Choose angular distance is too small, may make pick Angle too many, the actual machining woodworking engraving machine.
woodworking engraving machine introduces control mode can be divided into three kinds:
A, all the operations performed by computer control.
B, using single-chip microcomputer control.
C, USES the USB port to transmit data, the system has more than 32 MB of memory.
what are the reasons using wood engraving:
1, as the mechanized equipment than the artificial production efficiency is high, and the defective rate is extremely low.
2, woodworking carving machine mostly adopt the gantry structure, the maximum meet the limits of feed can be adjusted.
3, steel structure of heavy duty lathe bed, ensure the machine's overall stability, qualitative.
4, equipment with circular guide rail or square rail, bearing surface stability. Rack drive, stable transmission, ensure long time high-speed operation not deformation, not shake.
so when carved wooden door can guarantee the accuracy of the carved with beautiful, thus greatly improve the efficiency of wood production.
the volume of a relief value is negative, below the zero plane anaglyph and above all in the zero plane relief in effect identical. Is completely different. If relief most below the zero point, and make a path can lead to the Z axis engraving machine after stroke is not enough. This is don't want to see, can use any one of the following two methods to solve the problem:
solution 1:
1, connect all colors. Make the main color ( About white) Fill the 2 d view.
2, will be the main color attribute is set to flat surface. The height and zero plane under the relief height.
3, apply this setting to relief. So the embossment will move more than zero plane.
the solution 2:
1, the open position is set form. From the main menu option in the menu option to select the model position setting.
2, move the cursor in two dimensional check. To find the lowest value of Z axis ( The Z axis value appeared in the XYZ status bar)
3, the minimum benchmark pixels in the option to select the lower left pixel.
4, set the Z value method for one find the Z axis. For example, the actual location option. Assumptions that one find the Z axis - is the minimum location value 10 is the input value 10
5, application Settings. Pick my acceptance.
6, check whether get Z values needed for the Z value. Move the cursor in two dimensional check.
to move it relief carving machine Z axis in the process of the operation of the above, if the embossment deep below the zero plane. May appear the Z axis space is not enough, this kind of situation is generally because there is not enough space at the same time keep the positive and negative relief (Z Relief from the zero plane and move to the zero plane operating process, when the new relief, must assure ArtCA M there is enough space to keep the positive and negative Z axis of two relief) 。
in general the carved by the knife to complete some time due to the design area is larger between two lines or stroke is coarser place will not processing can produce so-called islands 'carving software provides two kinds of processing methods for disposing island processing and continuous way.
the so-called island processing, wood engraving machine 3 d engraving 3 d also called woodworking engraving machine for 'three dimensional Angle of' the function is according to my design and selection of cutting tool design. Is the above said some raw to the region with the method of the bottom of the milling process.
to remove the bottom of the milling, continuous carving mode should define its percentage 'overlap', refers to the milling for flat area as an initial plane, three-dimensional processing to continue. So fashioned out of actual depth is bigger than the designed depth, but not insurmountable engraving machine blade and the height of the handle.
processing can be appropriate when revise the pick angular distance, pick angular distance, three dimensional Angle of processing parameters. When processing large objects or use coarser tool, carry angular distance can increase accordingly. Usually, it is recommended to use the default value of 0. 1 mm. Choose angular distance is too small, may make pick Angle too many, the actual machining woodworking engraving machine.
woodworking engraving machine introduces control mode can be divided into three kinds:
A, all the operations performed by computer control.
B, using single-chip microcomputer control.
C, USES the USB port to transmit data, the system has more than 32 MB of memory.
Custom message
