Jinan Transon CNC Equipment Co., Ltd.
S I N C E 2 0 1 0
Latest products
Why stone carving machine knife, how to prevent stone machine - avalanche dao - Engraving machine _ _ _ _ CNC woodworking engraving machine engraving machine carving factory house
by：Transon
2020-07-17
>
why would collapse knife stone carving machine
the tool wear are mainly abrasive wear, the wear of cutting tool is larger, the influence of it is easy to cause the knife knife crack. This period is a very dangerous period, handled properly, may directly cause tool collapse failure. We see the tool wear is the main factor that leads to collapse knife.
and the processing of feed too fast or speed is not enough, the cutting tool quality is bad, turning processing is too big, tool clamping length is insufficient or shaking. Of course also and processing of stone, the stone material of different hardness is different.
tool force sudden increase or path is not correct or not shake or material are caused by the fastening lumps or spindle motor speed is not correct several reasons for this.
stone carving machine tool wear can be divided into three stages: initial wear, normal wear and tear, rapid wear. Began to wear stage of cutting tool wear main reason is the temperature of the cutting tool is low, did not reach the optimum cutting temperature.
how to reasonable use avoid stone carving machine knife under the
1, the cutting tool cutting temperature rise gradually to the reasonable temperature. Use the same processing parameters can be seen after running-in, comparison of the processing of the knives' service life was increased by more than 2 times. Running-in method is in keeping the reasonable use of spindle speed, the feed rate reduced to a half, the processing time at about 6 ~ 10 minutes.
2, stone carving machine knife is under the stone carving machine mechanical structure itself, the Z axis under the knife is not vertical, Z and X axis Angle is bad, result in the cutter carved using unbalanced force.
3, stone carving machine turning too deep, processing feed speed is too fast, or speed is not enough, the cutting tool reason of poor quality knife can also cause a stone carving machine crack.
stone carving machine collapse after the knife how timely processing
if the tool after the break, the operator should immediately stop machine, and then look at the current processing line number and the detailed record. Carefully check the cutting knife point for cutting knife blade, if you have removed. The most important thing is to analyze the main reason for the cutting knife and avoid it again next time.
and then is replaced, it should be noted that after changing the tool to define the origin, after the stone carving machine back to the workpiece origin two axis X/Y location is correct, but the Z axis need to be sure, it's mainly operates according to has to do graphic style definition.
if in the process of cutting knife we should stop at the first time for stone processing, then we need to write down the current processing job number, record the segment number. After good record segment number we need to check the cutting knife, make sure there are no cutting knife blade residues.
the two jobs are done we will need to be careful to find the cause of the cutting knife, after to find the reason why we need to change the cutting tool, find the serial number when cutting knife, a serial number and then processed in advance, pay attention to when we want to slow down some, because probably more hard cutting knife, second good to the new change of the cutting tool to get up to speed, etc.
why would collapse knife stone carving machine
the tool wear are mainly abrasive wear, the wear of cutting tool is larger, the influence of it is easy to cause the knife knife crack. This period is a very dangerous period, handled properly, may directly cause tool collapse failure. We see the tool wear is the main factor that leads to collapse knife.
and the processing of feed too fast or speed is not enough, the cutting tool quality is bad, turning processing is too big, tool clamping length is insufficient or shaking. Of course also and processing of stone, the stone material of different hardness is different.
tool force sudden increase or path is not correct or not shake or material are caused by the fastening lumps or spindle motor speed is not correct several reasons for this.
stone carving machine tool wear can be divided into three stages: initial wear, normal wear and tear, rapid wear. Began to wear stage of cutting tool wear main reason is the temperature of the cutting tool is low, did not reach the optimum cutting temperature.
how to reasonable use avoid stone carving machine knife under the
1, the cutting tool cutting temperature rise gradually to the reasonable temperature. Use the same processing parameters can be seen after running-in, comparison of the processing of the knives' service life was increased by more than 2 times. Running-in method is in keeping the reasonable use of spindle speed, the feed rate reduced to a half, the processing time at about 6 ~ 10 minutes.
2, stone carving machine knife is under the stone carving machine mechanical structure itself, the Z axis under the knife is not vertical, Z and X axis Angle is bad, result in the cutter carved using unbalanced force.
3, stone carving machine turning too deep, processing feed speed is too fast, or speed is not enough, the cutting tool reason of poor quality knife can also cause a stone carving machine crack.
stone carving machine collapse after the knife how timely processing
if the tool after the break, the operator should immediately stop machine, and then look at the current processing line number and the detailed record. Carefully check the cutting knife point for cutting knife blade, if you have removed. The most important thing is to analyze the main reason for the cutting knife and avoid it again next time.
and then is replaced, it should be noted that after changing the tool to define the origin, after the stone carving machine back to the workpiece origin two axis X/Y location is correct, but the Z axis need to be sure, it's mainly operates according to has to do graphic style definition.
if in the process of cutting knife we should stop at the first time for stone processing, then we need to write down the current processing job number, record the segment number. After good record segment number we need to check the cutting knife, make sure there are no cutting knife blade residues.
the two jobs are done we will need to be careful to find the cause of the cutting knife, after to find the reason why we need to change the cutting tool, find the serial number when cutting knife, a serial number and then processed in advance, pay attention to when we want to slow down some, because probably more hard cutting knife, second good to the new change of the cutting tool to get up to speed, etc.
Custom message
