Use carved mechanical and electrical spindle the note have?

Spindle motor is the basic guarantee for the machining fine vulture, the production of high precision, such as rotor side cone precision in 0. Within 002 mm, because of its high precision, a carved machine used in the most vulnerable link! However, this is not about carved machine service life of the spindle motor is low, in fact, as long as the operator according to the specification, carved machine spindle motor is relatively durable. In the use of carved technology must comply with the following specification: carved machine operators must be approved by the company's professional training, and, it is strictly prohibited without training operators use carved machine. Boot before use, first to ensure normal motor cooling circulatory system, and then open the spindle motor, it is strictly prohibited in no cooling conditions using the spindle motor. Working environment temperature is not higher than 30 ℃ and 30 ℃ when the environment temperature is higher than after should use air conditioning, or use the refrigerating machine for spindle motor forced cooling ( When using the spindle machine should be carried out in accordance with the refrigerating machine instructions) 。 Specific coolant used in the spindle motor cooling, cooling fluid must be clean. To timely added coolant, observe the temperature of the cooling fluid, when the temperature exceeds 30 ℃ cooling fluid to cool. Use carved machine must use the regulated power supply and uninterrupted power supply, in order to guarantee the reliability of the work. When he began to work every day, according to transfer from low speed to high speed spindle motor running principle, the acc preheat (step by step See the preheating process) , when the motor reaches the required speed and racing stable running, and then carry on the processing temperature stability. In this way can guarantee good processing precision. If downtime for more than two days or more, you must step from low speed to high speed of motor according to motor running in steps of no-load running in, after running-in through before using. To be in accordance with the principle of our company service personnel to provide with a knife for processing, carving knife in planning reasonable way to make sure that the spindle motor bearing, must avoid the vertical knife, it is forbidden to spindle motor overload, assure the normal service life of the spindle motor. It is forbidden to use the blade wear jig for processing. Still continue to use after the tool wear, axial force increased motor, lead to bearing damage, but also affect the precision and effect of sculpture. Operation are strictly forbidden to hit, hit the spindle electronic rotor side. The operator must pay attention to the Z axis when the knife, the cutting point to review the input parameters, such as cutting point to prevent wrong operation. To avoid in the process of operation such as impact, knife phenomenon of spindle motor bearing damage, once has the knife phenomenon, should stop immediately, so as to avoid high speed bearing greater harm team! Then, starting from the low speed to get up to speed, slightly longer time than normal working time, after the cloud know motor smoothly and normally begin to work. If improper operation, card head stuck in the motor rotor side, it is forbidden to use the method of tapping motor rotor head out card. Only when processing tools such as to take out the card head with forceps, but cannot damage motor rotor thread, at this point, the card head and the cap has been completely loss of accuracy, must be replaced immediately afterwards card head and the cap, or continue to use still will damage the motor rotor. When using the workpiece cutting fluid, the cutting fluid must go in the tool cutting parts, only then can have the effect of cutting tool and workpiece cooling, forbidden to cutting fluid on the pressure cap and electronic rotor end. Tool use spring card head card. In order to ensure the accuracy of the cutting tool with card and processing quality, also in order to avoid the pressure cap, the rotor is damaged, before each card and replace tool, must will ning of pressure cap clip, methods to ban the use of direct swap tool change knife! Must use gasoline or WD40 cleaner clean the card head and the cap! To regularly check and remove the residue inside the card head aperture, will head of inner hole and outside surface ( Including cone, end face, etc. ) Scrub clean, rotor and card head to cooperate on face, taper hole scrub clean again after a knife. According to the right way up and down cutter, cannot use brute force knife from top to bottom, to prevent rotor and pressure cap slide fastener. Don't use the spindle motor, around the clock to rest the spindle motor was at least two hours a day, so that the spindle motor can restore mechanical fatigue, so as to prolong the life of the spindle motor. Don't use has worn in knife tools and pressure cap. The special protection don't processing graphite materials. According to maintenance system for spindle motor for maintenance.